How to Choose Blackout Curtains for a Darker Bedroom
In June my bedroom starts getting light at about quarter past four, and for two summers I woke with it.

In June my bedroom starts getting light at about quarter past four, and for two summers I woke with it. I bought a pair of heavy blackout curtains, hung them on the existing rod, and woke at quarter past four again, this time looking at two bright vertical stripes down the wall where the fabric met the window frame.
That is the thing almost nobody mentions on the product page. A blackout curtain blocks light through the fabric, and the fabric was never where my problem was. The gaps were. Fixing a bedroom for darkness is mostly a measuring and mounting job, and the curtain itself is the easy part.
Where the light actually gets in
Hold a torch outside your window at night and have someone stand inside with the curtains shut. You will find four leaks, roughly in this order of size.
The sides come first. A standard curtain rod sits a few inches out from the wall, so the fabric hangs in a plane in front of the window with daylight free to travel round the edge and bounce off the side wall. Then the top, where light spills over the rod and washes the ceiling. Then the bottom, which matters less than people expect because light going down hits the floor rather than your eyes. Last, the fabric itself, which on a decent blackout panel leaks very little.
The practical consequence is that spending more on the panel rarely fixes the room. A $25 panel mounted properly beats a $90 panel on a short rod, and I have tested both on the same window.
What the labels on the packet mean
Curtain terminology is loose and partly invented by marketing teams, but there are real differences in construction behind the words. These are the categories you will meet.
| Label | How it is made | Light through the fabric | Typical price per panel |
|---|---|---|---|
| Room darkening or dimout | Dense weave, no coating | Noticeably dimmed, shapes still visible | $15 to $35 |
| Blackout, triple weave | Three layers woven together, black yarn in the middle | Around 90 to 97 percent blocked | $20 to $55 |
| Blackout, foam or acrylic backed | Fabric with a coated backing laminated on | Close to total through the fabric | $25 to $70 |
| Separate blackout liner | Hangs behind curtains you already own | Depends on the liner, often very good | $15 to $40 |
| Interlined custom curtain | Face fabric, blackout interlining, separate lining | Excellent, and the heaviest option | $120 and up |
Foam backed panels block the most light and are the cheapest route to a dark room, with two drawbacks worth knowing. The coating can crack after a few years of being pushed back and forth, and it does not like a hot wash or a tumble dryer. I wash mine cold and hang them damp so the weight pulls the creases out.
The liner option deserves more attention than it gets. If you already have curtains you like, a blackout liner hung on the same hooks behind them costs under $40 for most windows and gets you most of the way. It also lets you take the liner down in winter when you want the morning light back.
Measuring and mounting, which decides everything
This is the section I wish I had read first. Every number here is doing a specific job.
- Rod width. Extend the rod 8 to 12 inches (20 to 30 cm) beyond each side of the window opening. That overlap is what kills the vertical stripes.
- Curtain width. Total panel width should be about twice the rod length so the fabric still gathers when closed. Panels that stretch flat let light through at the weave and look mean.
- Rod height. Mount it 4 to 6 inches above the frame, or near the ceiling if you have the height. Higher looks better and gives you more fabric above the glass to catch spill.
- A return. Use a wraparound rod, or add a side bracket that pulls the leading edge of the curtain back to the wall. This single part, usually under $20, did more for my room than the curtains did.
- Length. Half an inch above the floor for curtains you open daily. Resting on the floor blocks slightly more light but collects dust and drags when you pull them.
Two small additions if you want the room genuinely dark. A pelmet or a simple fabric valance across the top stops the ceiling wash completely. And where two panels meet in the middle, overlap them by at least 4 inches and clip them together at the top with a curtain clip, because that centre seam opens itself overnight.
My own window took a 72 inch rod on a 48 inch window, two 52 inch wide foam backed panels, wraparound brackets, and about an hour with a drill. Total around $95. The stripes went away and I now wake up when my alarm says so.
The advice I would push back on
The standard recommendation is to make the bedroom as close to pitch black as possible and keep it that way all night. The first half of that is sound. There is reasonable evidence that even modest light during sleep is not neutral; a small 2022 sleep laboratory study found that a single night in a room lit to roughly 100 lux, about the level of a dim hallway bulb, raised overnight heart rate and next morning insulin resistance in healthy young adults. Street lighting through thin curtains can easily reach that.
The part I disagree with is keeping the room dark through to your alarm. Morning light is the strongest signal your body clock has, and a perfectly blacked out room removes it. After my first winter with foam backed curtains I was dark adapted from ten at night until eight in the morning, and I felt groggier for an hour after waking than I had with the old leaky curtains. That is not a scientific finding, it is one person's experience, but it matches what the timing research would predict.
What I do now is keep the room dark for sleep and arrange for light at the right end. On the two curtains I leave a hand width gap at one side from spring onward, which lets light in after about six. In winter I use a lamp on a plug timer set thirty minutes before the alarm, which cost roughly $12 and works better than I expected. Our piece on how bedroom lighting affects sleep goes further into the evening half of that equation.
When a blind beats curtains
Curtains hang in front of the window. A blind sits inside the recess, which changes the geometry in your favour. Fitted close to the sides with the right type of rail, a blackout roller blind can get a room darker than any curtain on a rod, because there is no path round the edge at all.
Three situations where I would choose the blind. A window in a deep recess, where a side channel kit traps the edges and the result is close to a cinema. A small or awkward window, such as a dormer or a bathroom sized pane in a box room, where full length curtains eat wall space you need. And a rented flat where you would rather not drill into the wall, since many blinds clip to the frame.
The combination is better than either alone, and it is what most hotels use: a blind for darkness, curtains over the top for the sound deadening and the look. If your room is tight on wall space, our guide to making a small bedroom feel bigger and calmer covers what to give up first. More on styling the room sits in our bedroom style section.
FAQ
Do blackout curtains really block all light?
The fabric on a foam backed panel comes very close. The installation almost never does. Expect a noticeable improvement from the curtain alone and near total darkness only once the sides, top and centre gap are handled.
Are blackout curtains worth it if I use a sleep mask?
A good mask is cheaper and more portable, and for many people it is enough. Curtains do two things a mask cannot: they cut heat coming through the glass on summer afternoons, and they help with noise a little. If you share the bed with someone who hates masks, the curtains settle the argument.
How do I stop light coming over the top of the curtain?
Mount the rod higher, use a wraparound rod so the fabric meets the wall, or fit a pelmet across the top. A fabric covered board about 5 inches deep, screwed above the window, is a weekend job and removes the ceiling glow entirely.
Can I wash blackout curtains?
Triple weave panels usually wash cold on a gentle cycle. Foam backed panels are the fussy ones: cold water, no fabric softener, no dryer, and hang them while still damp. Heat is what makes the backing peel away from the face fabric.
More in Bedroom Style
Bedroom Style
How to Choose a Bed Skirt That Stays Put and Looks Neat
The bed looked finished for about four days. Then the skirt had crept round on the box spring, one corner pleat sat on top of a...
Bedroom Style
How to Make a Small Bedroom Feel Bigger and Calmer
A small bedroom can feel like you are sleeping in a hallway: the bed fills the floor, the wardrobe door hits the frame, and...
Bedroom Style
How to Choose a Headboard That Fits Your Bed and Room
A bed without a headboard can look unfinished, and pillows slide down the gap against the wall every night.